Replacing clutch & brake levers: Difference between revisions

Line 14:

[[Image:13adjuster2.jpg|170px]]

~~[[Image:levers2-2.JPG|150px]]~~

~~Line up the slots on the adjuster and the perch for the clutch cable to come out.~~

[[Image:levers3-2.JPG|150px]]

~~[[Image:levers4-2.JPG|150px]]~~

Now you can remove the old cable from the handle bar end. Pull the cable out of the adjuster screw, pulling away from the handle. Align the cable end with the slot, and pull the cable end down, out of the handle as shown.

[[Image:18cableout.jpg|170px]]

[[Image:levers4-2.JPG|150px]]

Remove the pivot bolt lock nut. Make sure you do the nut before you try to take the bolt out.

Line 37:

Line 33:

[[Image:levers7-2.JPG|150px]]

Remove the lever. It may be tight, but once the bolt is removed, just pull it out. If you have trouble removing the lever, it may be that the choke/turn signal housing ~~kept~~ preventing the lever from getting past it~~. I actually disassembled that housing before I realized the real cause~~. The mount for the clutch lever is adjustable ~~- a~~ single bolt secures it. ~~The~~ clutch lever mount and the choke/signal housing ~~were~~ too close to each other on the handlebar, ~~by a couple of millimeters. I loosened~~ that mounting bolt slightly and ~~wiggled~~ the clutch lever mount slightly farther toward the center of the bike~~. Then everything fit just fine~~.

Remove the lever. It may be tight, but once the bolt is removed, just pull it out. If you have trouble removing the lever, it may be that the choke/turn signal housing is preventing the lever from getting past it. The mount for the clutch lever is adjustable up and down on the bar. A single bolt secures it. If the clutch lever mount and the choke/signal housing are too close to each other on the handlebar, loosen that mounting bolt slightly and wiggle the clutch lever mount slightly farther toward the center of the bike.

Install the new cable, pushing the cable end up into the slot, and pulling the cable into the adjuster.

@@ Line 14: / Line 14: @@
 [[Image:13adjuster2.jpg|170px]]
-[[Image:levers2-2.JPG|150px]]
-Line up the slots on the adjuster and the perch for the clutch cable to come out.
 [[Image:levers3-2.JPG|150px]]
-[[Image:levers4-2.JPG|150px]]
 Now you can remove the old cable from the handle bar end. Pull the cable out of the adjuster screw, pulling away from the handle. Align the cable end with the slot, and pull the cable end down, out of the handle as shown.
 [[Image:18cableout.jpg|170px]]
+[[Image:levers4-2.JPG|150px]]
 Remove the pivot bolt lock nut. Make sure you do the nut before you try to take the bolt out.
@@ Line 37: / Line 33: @@
 [[Image:levers7-2.JPG|150px]]
-Remove the lever. It may be tight, but once the bolt is removed, just pull it out. If you have trouble removing the lever, it may be that the choke/turn signal housing kept preventing the lever from getting past it. I actually disassembled that housing before I realized the real cause. The mount for the clutch lever is adjustable - a single bolt secures it. The clutch lever mount and the choke/signal housing were too close to each other on the handlebar, by a couple of millimeters. I loosened that mounting bolt slightly and wiggled the clutch lever mount slightly farther toward the center of the bike. Then everything fit just fine.
+Remove the lever. It may be tight, but once the bolt is removed, just pull it out. If you have trouble removing the lever, it may be that the choke/turn signal housing is preventing the lever from getting past it. The mount for the clutch lever is adjustable up and down on the bar. A single bolt secures it. If the clutch lever mount and the choke/signal housing are too close to each other on the handlebar, loosen that mounting bolt slightly and wiggle the clutch lever mount slightly farther toward the center of the bike.
 Install the new cable, pushing the cable end up into the slot, and pulling the cable into the adjuster.